What're your thoughts and feelings on Tools You Need to Install a New Bathtub ?
Installing a tub isn't precisely brain surgery, but it does need solid plumbing, carpentry, and occasionally, tiling abilities. Replacing an old bath tub with a new one is additionally a reasonably difficult job. If the old bathtub is conveniently easily accessible, the task can move rapidly; if you need to open a wall to remove the old bathtub as well as position the new bath tub, the job is much harder. In either instance, the task is within a home handyman's skills, although you will need an assistant to move out the old bathtub and also set in the new one. Make sure you have actually qualified yourself for the work and also are comfortable attempting it. As opposed to employing a service provider to take control of a halfway-completed job, it is much better to take into consideration utilizing one prior to you start. Possibilities are you may require a professional plumber to make tube links.
This short article will certainly help you mount a new bathtub in your shower room if you have currently acquired a new bathtub and also do not require to change the arrangement of your previous supply of water pipelines.
Your tools as well as material checklist need to consist of the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, after that the first thing you must do is detach the supply of water. After doing so, switch on the faucets to drain any water remaining in the system. The process of eliminating the existing faucets can be quite troublesome because of the limited access that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the faucets. Have a towel ready for the remaining water that will certainly originate from the pipes. When the supply pipes have actually been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the solitary taps from transforming during this process. Once the faucets have been gotten rid of, the holes in the bath/basin will have to be cleaned up of any type of old sealing compound.
Prior to carrying on to fit the new faucets, contrast the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, then a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end supplies a link to the existent supply pipes.
If you require to fit a monobloc, after that you will require decreasing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, place the faucet in the installing hole in the bath/basin making sure that the washing machines remain in location between the tap as well as the sink. Protect the tap in position with the manufacturer offered backnut. Once the tap is securely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular faucet connectors. The previous kind must be linked to the tap finishes first, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Bath tub
Making use of the two wooden boards under its feet, position the tub in the required placement. The wooden boards are practical in uniformly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following objective is to make certain that the tub is leveled all round. This can be achieved by checking the spirit level as well as changing the feet on the bathtub until the level reviews degree.
To set up taps, fit all-time low of the outermost adaptable tap port to the suitable supply pipeline by making a compression join; after that do the exact same for the other faucet.
Turn on the supply of water as well as examine all joints and new pipework for leaks as well as tighten them if essential. Load the bath tub as well as also examine the overflow outlet as well as the regular outlet for leaks.
Finally, take care of the bathroom paneling as defined in the producer's instruction manual. Tiling as well as sealing around the bath tub should wait till the bathtub has actually been made use of a minimum of when as this will certainly resolve it into its last placement.
Preparing for the Installment
To start with, the sustaining frame supplied with the bath ought to be fitted (if needed) according to the manufacturer's instructions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is important to ensure that if the faucet comes with a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps device to prevent pressure on the tub.
Fit the versatile faucet ports to the bottom of the two faucets using 2 nuts as well as olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you use every one of the provided washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should currently prepare to be fitted in its last setting.
Tiling Around the Tub
In the area where the bath fulfills the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to crack a stiff seal, causing the water to pass through the wall in between the bath and the tiling, bring about complications with dampness as well as feasible leaks to the ceiling below.
You can pick from a range of coloured sealers to assimilate your components and installations. They are offered in tubes and cartridges, and also are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to always fill up the tub with water before securing, to allow for the motion experienced when the bathtub is in usage. The sealant can fracture rather early if you do not take into account this motion before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally quickly available on the marketplace. It is a good idea to fit the tiles making use of waterproof or water resistant glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate reading about How to Install a Bathtub? Post a remark down the page. We would be pleased to know your ideas about this post. Hoping to see you back again in the near future. Loved our review? Please share it. Help somebody else check it out. I praise you for your time. Come back soon.
Your solution? Just a ring.